成形彈性夾與彈性板的連接利用彈性變形彈性元件的彈性力來實現保持架的緊固，并通過彈性元件與圓柱銷的組合來實現連接，這就要求保持架有足夠的空間，所以常用于連接大型夾具。T型徐州NSK軸承保持架。

The connection between the forming elastic clamp and the elastic plate uses the elastic force of the elastic deformable element to achieve the fastening of the cage and the combination of the elastic element and the cylindrical pin to achieve the connection, which requires the cage to have enough space, so it is often used to connect large clamps. T-type Xuzhou NSK bearing cage.

1)檢查機械密封的類型和規格，以滿足設計圖紙的要求。所有零件（尤其是密封件和輔助密封件）均未受損、變形和破裂。如果有缺點，**須更換或修理。

1) Check the types and specifications of mechanical seals to meet the requirements of design drawings. All parts (especially seals and auxiliary seals) are undamaged, deformed and cracked. If there are any shortcomings, ** must be replaced or repaired.

2)檢查機械密封各部分的尺寸、表面粗糙度和平行度是否滿足設計要求。

2) Check whether the dimensions, surface roughness and parallelism of each part of mechanical seal meet the design requirements.

3)使用小彈簧機械密封時，檢查徐州NSK軸承長度是否與小彈簧的剛度相同。

3) When using small spring mechanical seal, check whether the length of Xuzhou NSK bearing is the same as the stiffness of small spring.

4)檢查主機的位移、擺動和撓度是否滿足技術要求，密封室是否滿足安裝尺寸以及密封蓋是否垂直于軸。一般要求是：軸的位移不超過（+0.5mm）；軸的擺動（衰減）不超過0.06mm；軸的**大撓度不超過0.05mm；密封蓋和密封墊片之間的接觸面不垂直于軸。軸。心線。差值為0.03～0.05mm。

4) Check whether the displacement, swing and deflection of the main engine meet the technical requirements, whether the sealing chamber meets the installation size and whether the sealing cover is perpendicular to the shaft. The General requirements are as follows: the displacement of the shaft does not exceed (+0.5mm); the swing (attenuation) of the shaft does not exceed 0.06mm; the large deflection of the shaft does not exceed 0.05mm; and the contact surface between the sealing cover and the sealing gasket is not perpendicular to the shaft. Shaft. The heart line. The difference is 0.03-0.05 mm.

5)應保持清潔，特別是徐州NSK軸承旋轉環、靜環密封面和輔助密封環表面應無雜質和灰塵。嚴禁用臟布擦拭密封面。

5) Should keep clean, especially Xuzhou NSK bearing revolving ring, static ring sealing surface and auxiliary sealing ring surface should be free of impurities and dust. It is strictly forbidden to wipe the sealing surface with dirty cloth.

6)敲擊工具，以防止損壞密封元件。

6) Knock tools to prevent damage to sealing elements.

兩個線程是用線程固定的。區別在于**一螺桿承受拉應力，而**二螺桿承受壓剪應力。

Two threads are fixed by threads. The difference is that ** one screw bears tensile stress while ** two screw bears compressive shear stress.

更換軸承時，不必在設備附近拆卸軸承，縮短了軸承總安裝時間，降低了工作要求，大大縮短了主機停機時間，提高了徐州NSK軸承生產效率。基于上述優點，分體軸承的應用越來越廣泛。

When replacing bearings, it is not necessary to disassemble bearings near the equipment, which shortens the total installation time of bearings, reduces the working requirements, greatly shortens the downtime of the main engine, and improves the production efficiency of NSK bearings in Xuzhou. based on the above advantages, split bearing is more and more widely used.

結論：

Conclusion:

單個的軸承保持架通常是兩個半結構，安裝后組裝和連接。對于籠子的尺寸和空間有一定的要求。不同的連接方式會影響軸承的尺寸和數量，進而影響軸承的性能。

A single bearing cage is usually two and a half structures, assembled and connected after installation. There are certain requirements for the size and space of the cage. Different connection modes will affect the size and number of bearings, and then affect the performance of bearings.

文章來自：徐州SKF軸承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章來自：徐州INA軸承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章來自：徐州NSK軸承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757